{"product_id":"aim-mychron-egt-t12-fine-tip-short-life-sensor","title":"AiM MyChron EGT T12 Fine-Tip Sensor | Short-Life","description":"\u003ch2\u003eAiM MyChron EGT T12 Fine-Tip Sensor\u003c\/h2\u003e\u003cp\u003eThe AiM MyChron EGT T12 Fine-Tip Sensor is a K-type thermocouple for compatible exhaust-gas-temperature measurement with an AiM logger. It is installed in the exhaust header pipe using a suitable bung fitting, which is available separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eShort-life, high-performance item:\u003c\/strong\u003e this fine-tip sensor is not recommended for long-term use with a kart engine because the tip is likely to fail. There is no warranty on this item. Treat it as a performance consumable and inspect it regularly.\u003c\/p\u003e\u003chr\u003e\u003ch2\u003eEGT sensor application\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eK-type thermocouple\u003c\/strong\u003e for compatible exhaust-gas-temperature measurement.\u003c\/li\u003e\n\u003cli\u003eDesigned for installation in the exhaust header pipe.\u003c\/li\u003e\n\u003cli\u003eRequires a compatible AiM logger and the correct bung fitting.\u003c\/li\u003e\n\u003cli\u003eUseful for monitoring exhaust temperature during kart testing, tuning, and data analysis where the connected AiM system supports the channel.\u003c\/li\u003e\n\u003cli\u003eShort-life fine-tip construction intended for high-performance use, not indefinite service.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eCheck the logger model, connector, thermocouple wiring, installation position, exhaust temperature, and available channel configuration before ordering. This is a sensor, not a data logger. Readings are only useful when the sensor is installed correctly and the connected AiM logger is configured for the appropriate input.\u003c\/p\u003e\u003chr\u003e\u003ch2\u003eInstallation and care\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eUse a suitable exhaust bung and install the probe where it can measure a representative exhaust-gas temperature.\u003c\/li\u003e\n\u003cli\u003eKeep the probe and wiring clear of moving, hot, or abrasive components beyond the intended measurement point.\u003c\/li\u003e\n\u003cli\u003eInspect the fine tip, cable, connector, and bung after each session.\u003c\/li\u003e\n\u003cli\u003eReplace the sensor if the tip is damaged, readings become implausible, or the wiring shows heat or mechanical damage.\u003c\/li\u003e\n\u003cli\u003eAllow the exhaust system to cool before inspection or removal.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eInstallation should be completed by someone familiar with kart exhaust systems, thermocouple wiring, heat management, and the connected AiM logger.\u003c\/p\u003e\u003chr\u003e\u003ch2\u003eAiM MyChron support\u003c\/h2\u003e\u003cp\u003eUse the \u003ca href=\"\/pages\/aim-race-studio-3-knowledge-hub\"\u003eAiM Race Studio 3 Knowledge Hub\u003c\/a\u003e for compatible configuration and data-analysis workflows. Visit \u003ca href=\"\/pages\/aim-downloads-documentation\"\u003eAiM Downloads \u0026amp; Documentation\u003c\/a\u003e for official live AiM software, firmware, and documentation sources.\u003c\/p\u003e\u003chr\u003e\u003ch2\u003eEGT sensor FAQ\u003c\/h2\u003e\u003cdiv\u003e\n\u003cdetails\u003e\u003csummary\u003eWhat type of sensor is this?\u003c\/summary\u003e\u003cp\u003eThis is a K-type thermocouple with a fine tip for compatible exhaust-gas-temperature measurement.\u003c\/p\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eWhere is the sensor installed?\u003c\/summary\u003e\u003cp\u003eIt is installed in the exhaust header pipe using a suitable bung fitting, which is available separately.\u003c\/p\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eIs this sensor suitable for long-term kart use?\u003c\/summary\u003e\u003cp\u003eNo. The listing identifies it as a short-life, high-performance item and warns that the tip is likely to fail with long-term kart-engine use. There is no warranty on this item.\u003c\/p\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eWill it work with every AiM logger?\u003c\/summary\u003e\u003cp\u003eCompatibility depends on the AiM logger, connector, wiring, channel configuration, and thermocouple input requirements. Confirm the exact logger before ordering.\u003c\/p\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eIs the exhaust bung or logger included?\u003c\/summary\u003e\u003cp\u003eThe bung is listed as available separately, and this product is a sensor rather than a logger. Confirm the final kit contents and the required AiM logger before ordering.\u003c\/p\u003e\u003c\/details\u003e\n\u003c\/div\u003e\u003chr\u003e\u003cp\u003eFor AiM MyChron compatibility, exhaust bung requirements, wiring, or kart EGT setup advice in New Zealand and Australia, \u003ca href=\"\/pages\/contact-our-team\"\u003econtact Harris Race Radios\u003c\/a\u003e before ordering.\u003c\/p\u003e","brand":"AiM","offers":[{"title":"Default Title","offer_id":48747718836443,"sku":null,"price":185.0,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0696\/6670\/1531\/files\/egtshortlife2.avif?v=1778024717","url":"https:\/\/harrisraceradios.com\/products\/aim-mychron-egt-t12-fine-tip-short-life-sensor","provider":"Harris Race Radios","version":"1.0","type":"link"}